 |
 USB 25 SATA Hard Drive Disk Case Enclosure Laptop Blk  US $7.98
|
 Sony Vaio VGN FW390 164 Laptop Genuine Hard Drive Caddy with Screws US $7.97
|
 Toshiba 25 40gb SATA Laptop Hard Drive MK4034GSX US $14.99
|
Illustrated How To Replace A Laptop Hard Drive
A year ago, I bought a dell e1505 notebook cheaply.but I have replaced almost all of the laptops accessories during the year.now, I must replace the hard drive,but how do I replace~~~
Don’t rush into replacing the hard drive before troubleshooting the problem. The first step I take when working on any laptop or notebook computer is to remove the battery. Even if the power button is well protected, like under the closed lid of the screen, it doesn’t mean that the power might not come on due to a mechanical jolt or a short when you’re working on the innards, so the best bet is to just get the battery out of there.
Laptop batteries generally require two actions to remove them. In this case, the lock is on the front edge of the case, and it slides to the side. After the lock is released, the battery slides back just an inch or so to release from the connector, after which it’s lifted out and removed.
There are two basic scenarios for laptop hard drive replacement, the easy access scenario and thetake the whole laptop apart scenario. This Toshiba notebook is the easy access scenario, at least as far as exposing the drive goes. The hard drive is concealed behind a removable panel on the bottom of the laptop, which is held in place with one long screw.
As we lift the lid over the hard drive, you can see the long plastic tube that serves both as a screw guide and as a mechanical support. It should be immediately apparent that the dell e1505 hard drive isn’t going anywhere without the cage either being removed first or coming with it.
Closer inspection shows that this hard drive mounting system relies on the cage being attached to the hard drive before the hard drive is installed in the laptop. The only things that secures the hard drive and cage in the laptop are the power and data connector on one end, and a spring steel tab on this end. The picture to the left shows how the whole edge of the cage has to be pushed in to get the tab past the the plastic stub that holds it into place.
Once the locking tab clears the stub projection that holds the hard drive cage in place, the end still has to be lifted up till it clears the bottom of the laptop. There’s simply no room within the laptop bay to pull the hard drive back and disengage from the mating connector. One the cage clears the laptop, it takes a bit of force to pull the hard drive out on as shallow an angle as possible.
The first step in replacing the hard drive is removing the cage from the old drive, which is held in place with four screws. Make sure you note which way the cage goes on the old drive before you take it off, because it will need to be mounted on the new drive the same way, even though more than one orientation may be possible. You can see the corner of the new drive in the picture, in case you thought we only had one:-)
Once the replacement e1505 hard drive is mounted in the cage (same brand in this instance, though it doesn’t need to be), the whole assembly can be reinstalled in the laptop. Again, keep the drive on as shallow an angle as possible, ie, close to the bottom of the laptop, as you slide the pins into the connector. The close tolerances on the laptop bay usually make it impossible to mate the connector improperly.
If you worry about prying the drive against the connector when depressing the end of the cage so the tab clears the locking ear, you can hold the top edge of the cage out as you pry the tab in, as I’m doing here. Laptop hard drives aren’t terribly rugged, they’re so light and slim that I hate putting any more mechanical stress on them than I have to. Replacing laptop hard drives is a bit nerve racking for people who haven’t done it before, but as long as you don’t use an unreasonable amount of force, it should work out fine.
We replace the lid and use the long screw to reattach it to the bottom of the laptop. The emergency restore CD that comes with the laptop is used to reload all the software on the PC, but your data is gone unless you backed it up.Since the laptop hard drive we replaced in this example was a total brick, I figured I’d open it up (below) so you could take a look inside. The shiny circular thing is called a platter, on which the data is magnetically recorded and read by a read/write head on the end of the arm (currently in its park position away from the platter). The noise you here when your hard drive is operating is the arm swinging in and out over the surface of the platter, which spins under the read write head to provide access to all the usable locations on the drive.
About the Author
Udtek.com delivers high quality laptop batteries, laptop AC adapters, Laptop keyboards, Lcd chargers, DVD drivers, Scooter chargers and more. Our unique product lines of over 1000 diverse accessory power products and replacement batteries and adapters provide our customers with an extensive selection of the best quality products available.
How to Easily Install a Laptop Hard Drive - SYSTM Best of
